8 résultats trouvés
- 15 août 2008, 16:47
- Forum : International Board
- Sujet : G5 Reverb or Tremolo
- Réponses : 3
- Vues : 11283
Re : G5 Reverb or Tremolo
I have built the Version 3. By now there are just some simple Modifications planned like a Master Volume and a line out.And hopefully a Reverb or a Tremolo. The Plan looks nice, does it work with G5V3 also? I have some other question too, I would like to built an 8 Ohms and a 4 Ohm Output, can I wir...
- 13 août 2008, 20:09
- Forum : International Board
- Sujet : G5 Reverb or Tremolo
- Réponses : 3
- Vues : 11283
G5 Reverb or Tremolo
Hi I'm going to rebuild my G5, because it was the first amp I really made and it just looks like it. Now I think I am more experienced, because I built a lot of effects a basspreamp and so on. But I would like to build in some modifications. Some are very well described in the manual but then I had ...
- 02 sept. 2007, 15:55
- Forum : International Board
- Sujet : G5 Questions
- Réponses : 8
- Vues : 14408
Re : G5 Questions
Okay, I think I will try to replace them and make mesaures if it fits. I can use the bias document in the dowload area. Okay two more questions and I'm done. I'm planning to install an triode/Pentode switch. But I'm not sure what switch I should use and how to make the wiring. From the Pin 4 of V2 w...
- 02 sept. 2007, 11:30
- Forum : International Board
- Sujet : G5 Questions
- Réponses : 8
- Vues : 14408
Re : G5 Questions
Thank you for your answers, I was on vacation and now I'm back. My G5 is built and it is working. (After some Troubleshooting with the TT Forum) But I have a question about the tubes. A lot of the builders of the previous version said that every tube can be put into the G5 and you don't have to worr...
- 09 août 2007, 15:09
- Forum : International Board
- Sujet : G5 Questions
- Réponses : 8
- Vues : 14408
Re : G5 Questions
Thanks a lot.
Is it necessary to make a little hole or can I just drive the screws for the tube sockets in the chassis?
In the layout you made the ground on the screws of the transformers. Is this alright?
Is it necessary to make a little hole or can I just drive the screws for the tube sockets in the chassis?
In the layout you made the ground on the screws of the transformers. Is this alright?
- 08 août 2007, 14:29
- Forum : International Board
- Sujet : G5 Questions
- Réponses : 8
- Vues : 14408
G5 Questions
I said I'll be back and guess what? I am back! The G5 is my first amp and I built only a few stompboxes before. Now I have a problem with the screws. The kit was deliviered with a screw kit but I'm not really sure what screw to use for what. There are many smaller, fatter ones (ca. 4 cm diameter) an...
- 07 août 2007, 16:09
- Forum : International Board
- Sujet : New version of G5 released!!! G5v3
- Réponses : 8
- Vues : 14663
Re : New version of G5 released!!! G5v3
Thank you, that was exactly what I'm looking for. And very quick answer, if have more questions I will be back. 8)
- 07 août 2007, 14:48
- Forum : International Board
- Sujet : New version of G5 released!!! G5v3
- Réponses : 8
- Vues : 14663
Re : New version of G5 released!!! G5v3
Hi
Is the complete layout still in progress or did i miss it?
Greetings
Is the complete layout still in progress or did i miss it?
Greetings